A Reefer Run-Hour Documentation Log for Temperature Loads
A reefer run-hour log that records engine hours, fuel, pre-cool, and temperature settings so refrigerated loads stay defensible from pickup to delivery.
Published: September 18, 2026.
Temperature records are the first thing anyone looks at when a refrigerated load goes wrong. They show what the box did. They do not show how hard the refrigeration unit had to work, how much fuel it consumed, or whether it was in the right mode. When a customer asks why a load ran warm, a temperature chart alone often cannot answer.
A reefer run-hour documentation log fills that gap. It records the unit's running hours, fuel, setting, and mode at each checkpoint, alongside the time and location. Together with the temperature record, it gives the office a full picture of the trip and a defensible file for any question that follows.
Separate the three records
Refrigerated freight generates three different records, and they should not be mixed.
- The temperature record. What the cargo space and the supply and return air did.
- The run-hour log. How many hours the unit ran, in what mode, and with how much fuel.
- The service record. When the unit was last serviced and what was repaired.
Each answers a different question. A claim review usually needs all three. The run-hour log is the one most often missing.
Fields the log needs
| Field | Purpose |
|---|---|
| Load and unit identifiers | Ties the log to the trip |
| Tractor, trailer, and reefer unit | Identifies the equipment |
| Date, local time, and location | Fixes each checkpoint |
| Engine or unit hours | Tracks runtime |
| Fuel level | Prevents a run-dry failure |
| Set point and mode | Confirms the operating plan |
| Box temperature reading | Ties runtime to result |
| Pre-cool start and finish | Documents the pull-down |
| Exception note | Records anything unusual |
Keep the checkpoints consistent so the data is comparable: at pickup, at every fuel stop, at each rest stop of any length, and at delivery.
Start with the pre-cool
Pre-cooling is where many temperature problems begin. The unit should pull the box down to the set point before the doors open, not while the freight is loading. Record the pre-cool start time, the finish time, and the box temperature when loading began.
If the customer requires a specific pre-cool temperature, record it and verify the box reached it. A load that begins warm asks the unit to catch up for the entire trip, which raises runtime and fuel use and shortens the margin for any later failure.
Log every checkpoint the same way
At each stop, record the same fields in the same order.
- Date, local time, and location.
- Unit hours.
- Fuel level.
- Set point and operating mode.
- Box and air temperature readings where available.
- A note for any change or concern.
The comparison over the trip is what makes the log useful. A unit that normally runs a few hours between checkpoints and suddenly records a large jump may be working too hard. That pattern is worth a maintenance conversation before it becomes a failure on the road.
PRO TIP Photograph the unit's display at each checkpoint. A timestamped photo of the hours, fuel, and set point is quick to take and hard to dispute later.
Watch fuel and runtime together
A reefer unit that runs longer than expected burns more fuel and may indicate an airflow, door, or refrigerant problem. Track fuel level against run hours so the pattern is visible. Do not let the unit run low on fuel on a long stretch, because a fuel-starved unit stops cooling and the freight is at risk.
If the unit is running continuously to hold temperature, check the obvious causes first: door seals, curtain condition, and whether the box was properly pre-cooled. Record the observation and route a maintenance request under the carrier's policy. The Truck Maintenance Due Board is a natural place to track the follow-up.
Handle a failure with documentation
If the unit fails, follow the carrier's breakdown procedure. Record the failure time, the box temperature at the time, the ambient conditions, the repair attempt, and the time the unit returned to service. Notify the customer according to the load agreement. Do not continue with an unrepaired unit unless the responsible party gives written direction.
A failure with good documentation is a manageable claim. A failure with no timeline is a dispute. The run-hour log is often the record that shows whether the unit was already struggling before it stopped.
Close and review the log
At delivery, record the final readings and confirm the seal and temperature. File the log with the bill of lading and the temperature record. Each week, sample a few completed loads and confirm the checkpoints are present and complete.
Track exceptions by cause: door seal issues, pre-cool misses, fuel shortages, and unit faults. A pattern in one trailer or one customer's loading practice points to a specific fix. For securement and general operating rules, confirm current guidance through the Federal Motor Carrier Safety Administration, and follow the equipment maker's service instructions for the unit itself.
What to do next
Use this log with A Reefer Temperature Document Handoff and Reefer Temperature Exception Log. If reefer questions keep reaching management without a clear record, contact LogisticsTrucks with one trip and the decisions your team must keep.
The bottom line
A reefer load needs more than a temperature chart. Track the run hours, the fuel, the mode, and the checkpoints alongside it, and the office can explain the trip and catch a failing unit early. The log is small, repeatable, and one of the best protections a refrigerated carrier can keep.